|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
N55 Oil Filter Housing Gasket ; Do It!
|
|
10-22-2014, 08:46 AM | #1 |
New Member
16
Rep 27
Posts
Drives: 2016 BMW M328I & 2013 BMW 328i
Join Date: Feb 2013
Location: Hingham MA
|
N55 Oil Filter Housing Gasket ; Do It!
Heads up mine was leaking on my 2011 335i @ 70K miles ; tech at BMW dealership reported that oil had leaked past the gasket into the cooling system and contaminated the coolant! The gasket was replaced and the complete cooling system had to be flushed with detergent, then water then refilled with antifreeze.... Adviser said job was quoted @ $1200 but adjusted to $500 due to BMW goodwill. Now warrantied for 2 years / unlimited miles. My advice is to N55 owners is to preventive replace! Don't wait for cross contamination!!
|
10-22-2014, 08:52 AM | #2 |
Colonel
426
Rep 2,136
Posts |
My advice... if it ain't broke, don't fix it...
__________________
JB4 G5 w/ Backend flash - Walbro 450lpfp - VRSF DPs - VRSF 5" stepped IC - DCI - ER CP w/ Tial BOV - 335is clutch |
Appreciate
0
|
10-22-2014, 02:35 PM | #4 |
New Member
16
Rep 27
Posts
Drives: 2016 BMW M328I & 2013 BMW 328i
Join Date: Feb 2013
Location: Hingham MA
|
N55 oil filter housing gasket
It may not be broke but my point is spending a little now will SAVE you MEGA $$ later.... DUH
|
Appreciate
0
|
10-22-2014, 04:31 PM | #5 |
Private
8
Rep 88
Posts |
It has nothing to do with how the engine is assembled or what day it was assembled. I did the replacement of the rubber gasket on my oil filter housing two weeks ago (BTW, one of the bolts is very difficult to get to and I had to buy a 1/4 inch drive star socket with a universal joint to get at it). Once I had the manifold off, the gasket looked as if it had melted in place and was spreading out towards the passages. Basically, BMW's supplier used an inferior material that degrades over time. This is why they leak and I don't think there is anything you can do to prevent it. We drive $40k ticking time bombs ...
I know some forum members theorize that the gasket material can break away and ruin the coolant pump. That's not a bad theory and is even more reason to fix this oil leak before more havoc is wreaked. |
Appreciate
1
StradaRedlands4919.50 |
10-22-2014, 06:02 PM | #7 | |
Lieutenant
19
Rep 595
Posts |
Quote:
|
|
Appreciate
0
|
10-22-2014, 06:03 PM | #8 |
Lieutenant
19
Rep 595
Posts |
|
Appreciate
0
|
10-22-2014, 06:07 PM | #9 |
Fuck it dude, let's go bowling.
881
Rep 2,477
Posts |
The difficulty isn't one of replacing the actual gasket, but rather one of gaining access to the housing bolts. Dat intake manifold. On the N54, you basically have to remove the intake manifold to get access to one of the OFH bolts. So the question was really - does the N55 have the same issue?
__________________
1M. Previously: '13 135is; '07 E90 335i; '02 325i; '99 Z3; '98 328is; '87 L6; '77 320i
|
Appreciate
0
|
10-22-2014, 08:55 PM | #10 |
Captain
59
Rep 675
Posts |
Be advised that the warranty is on the part only. If i remember correctly $15. The labor is out of pocket!
|
Appreciate
0
|
10-24-2014, 10:46 AM | #11 | |
Private First Class
17
Rep 187
Posts
Drives: SGM e92 335i M-sport
Join Date: Feb 2011
Location: DFW
|
Quote:
|
|
Appreciate
0
|
03-03-2017, 09:24 AM | #12 | |
Major
494
Rep 1,416
Posts |
Quote:
As I was researching how to DIY this I came across this video and two things occurred to me. 1. Once the housing opens coolant and oil spills out! Is there a risk of cross contamination there? Are people DIYing this with a coolant flush and oil change at the same time? 2. Because the coolant is exposed are we required to bleed and refill coolant after the DIY?
__________________
Last edited by delmarco; 03-03-2017 at 10:21 AM.. |
|
Appreciate
0
|
03-03-2017, 11:16 AM | #13 |
Colonel
1207
Rep 2,025
Posts |
Yes, contamination can occur, but it's minimal. best to do this service while also doing an oil change. Bleeeding the cooling system would be another best practice. When all buttoned back up just run the electronic procedure. Turn car to on position, put heat to full, hold down gas for 10 seconds, and let the electronic pump do its thing for roughly 10minutes (dont open/close doors as it will interrupt the bleed process).
|
Appreciate
0
|
03-08-2017, 01:38 AM | #14 | |
Colonel
295
Rep 2,015
Posts |
Quote:
But this time on top of our inferior gasket I put permatex Ultra copper gasket maker. Just follow the instructions on tube. 2.5 years.... No issues. |
|
Appreciate
0
|
03-29-2017, 11:08 AM | #15 |
Major
494
Rep 1,416
Posts |
My Filter housing is icky with white spots all over. Agouls I just go ahead and spend the extra money replacing the filter body?
Now I noticed a new filter housing comes with the gasket already installed...does that make this DIY easier?
__________________
|
Appreciate
0
|
04-13-2017, 11:44 AM | #16 |
New Member
16
Rep 27
Posts
Drives: 2016 BMW M328I & 2013 BMW 328i
Join Date: Feb 2013
Location: Hingham MA
|
NO when parts are replaced at ANY BMW dealer they are warranteed minimum 2 years unlimited mileage parts AND labor
|
Appreciate
0
|
04-20-2017, 04:55 PM | #17 |
Lieutenant Colonel
480
Rep 1,600
Posts |
The white stuff is just unsealed alloy surface corrosion. Hit it with some scotchbrite if you really must.
All that has been said already in this thread is true. The gasket appears to melt and fill the channels of the casting, so the gasket is no longer tall enough to be a gasket. Only use genuine gaskets for this job, not worth mucking around with aftermarket ones. N54/N55 dont forget to replace the two small orings for your oil cooler line connection. Cross contamination is possible if left unfixed for a long time. During repair, some slight cross contamination is possible but it's negligible if you take precautions. I wouldnt flush the cooling system but i would change the oil. - Remove the oil filter and suck out all remaining oil in the housing - Open the coolant cap to relieve any pressure - Remove the serpentine belt and cover your toothed pulleys. Buy a new belt if you see flat spots, melted rubber on the flat idler pulleys or other signs of wear due to oil contamination - Inspect top coolant hose and the smaller one beneath the housing held by two 10mm bolts (the Mickey Mouse one). Buy new hoses if you see any swollen rubber - Remove the top coolant hose (big one) to allow most of the coolant to escape from the housing. - N54/N55 you must elevate or remove the intake manifold to access one bolt. I usually just elevate and use a skinny wobbly extension. - The second difficult bolt is the one pointing downwards near the Mickey Mouse coolant hose connection to the head. If your hose is not swollen, id suggest using a 12pt 8mm spanner carefully to remove the bolt. Alternatively, remove the Mickey Mouse connection and use normal etorx sockets. - Slacken all bolts before removing housing from vehicle |
Appreciate
1
ja4an9.00 |
01-15-2019, 08:11 AM | #18 | |
Private First Class
45
Rep 149
Posts |
Quote:
__________________
2011 335I, E90, AT, Sport Package, FBO, Eibach 1" Lowering Kit w/ Koni Orange. MHD, 88k miles 2nd owner - Sold
2003 330XI, MT, bone stock, 160k miles - Sold 1988 325I Coupe, MT - Retired, 280k miles - Sold 2019 X7 XDRIVE 40I - Wife's |
|
Appreciate
0
|
01-15-2019, 03:49 PM | #19 |
Major
1009
Rep 1,268
Posts |
Folks if you work on cars this is an easy DIY, I have done it 3 times, the first time I did not torque the bolts correctly and did not change the second seal which is on the OFH, there is one between the block and the OFH and a second between two parts of the OFH. You need to do both since they both go bad at the same time.
I always changed my gasket when I did the oil change and never had an issue with Coolant leaking out. One of the way to know your OFH is leaking besides the fact you have oil all over the front of your motor you will see oil in the coolant reservoir. |
Appreciate
0
|
01-15-2019, 03:57 PM | #20 |
Captain
266
Rep 952
Posts |
Just did mine two weeks ago. That 3rd bolt under the intake manifold is a pain to get to, but if you loosen the intake manifold, you can get a 1/4" drive torx socket on it.
Also - some people have trouble with the bolt on the underside front near the coolant hose. If you buy a closed end /box torx wrench, it is easy. You can leave the coolant hose in place and not worry about replacing it.
__________________
bone stock
|
Appreciate
0
|
01-29-2019, 09:33 AM | #21 |
Major
494
Rep 1,416
Posts |
Another helpful video:
__________________
|
Appreciate
0
|
01-31-2019, 08:09 PM | #22 |
Lieutenant
113
Rep 513
Posts
Drives: 2008 335i
Join Date: Jan 2018
Location: Vancouver
|
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|