[coupedream]

Originally Posted by alex_07

someone managed to encode an nbt evo ? I would also like to install the aliexpress version. thank you.

Yes I have a retrofitted nbt evo coded for color ambient lights.

[alex_07]

Originally Posted by coupedream

Yes I have a retrofitted nbt evo coded for color ambient lights.

Could you tell me the steps you took? Does it show you the right colors? thanks

[coupedream]

Originally Posted by alex_07

Could you tell me the steps you took? Does it show you the right colors? thanks

The colors are not right unfortunately. I don't know how to get that right. But the kit is self explanatory. Taps into the idrive controller. You need to pin out empty spots to run wires to doors. Then coding.

[alex_07]

could you give me a link to the ones you bought for the 4 series gran coupe?

[Hypermile]

Originally Posted by coupedream

Had it for awhile. I didn't code it myself but it's out there on forums.

What's with the cryptic answer? Why is the coding so secretive? Where is it "out there"?

[eff32fl]

Originally Posted by Hypermile

What's with the cryptic answer? Why is the coding so secretive? Where is it "out there"?

I recall finding a post telling how to modify the values of the OEM colors. Additional colors would be added to the same location I'd assume. I'll see if I can find the post and will report back.

[Hypermile]

^ Appreciate you!

[coupedream]

Originally Posted by Hypermile

What's with the cryptic answer? Why is the coding so secretive? Where is it "out there"?

I don't code. I did see it on AliExpress a long time ago in pictures of the led kit but I don't know where it's at. It's not secretive. It's out there. Again, I'm not a coder. Steve coded my car for the led lights.

[coupedream]

Originally Posted by alex_07

could you give me a link to the ones you bought for the 4 series gran coupe?

I bought 5 series ones and trimmed them to fit. It's a lot of work, you have to remove the trim and dremel and glue to fit the led strip. Then I used wire ties and glue to fit the blue trim back in place. See pics in above response.

[Hypermile]

Originally Posted by coupedream

I don't code. I did see it on AliExpress a long time ago in pictures of the led kit but I don't know where it's at. It's not secretive. It's out there. Again, I'm not a coder. Steve coded my car for the led lights.

Thanks for clarifying. I contacted a vendor on Ali WRT coding. I will share the response here.

[Hypermile]

Ok, after some digging, I found the seller who has a pic of the coding that is required to make it work on NBT cars. I don’t have pictures hosting subscription so I’ll post the link here and hopefully someone can post the picture of the coding. Of note, they are using BMWAi to code. https://m.aliexpress.com/item/100500...b2156d9&gclid=

[eff32fl]

Originally Posted by eff32fl

I recall finding a post telling how to modify the values of the OEM colors. Additional colors would be added to the same location I'd assume. I'll see if I can find the post and will report back.

Sorry the link I found previously is for the X5, which has a BDC module but the F30/F32 doesn't have BDC. I'm guessing it's in FEM. The X5 owners seem to have slightly different folder options depending on software updates. The colors are stored in hex form in R/G/B values. Refer to the below post.

https://f15.bimmerpost.com/forums/sh....php?t=1205119

A few color options and links to find colors in RGB and convert to hex from the same post.

https://f15.bimmerpost.com/forums/sh...3#post24418293 (post 124)

The 3 groups (dash, doors, footwell) you have to worry about from same post.

https://f15.bimmerpost.com/forums/sh...1#post24459531 (post 140)

This isn't a "how to" for our cars but should get you going in the right direction. Hope this helps.

[Persian]

Hello, if anyone needs the coding values ​​for the BMW models with FEM, for example F30/F31....

HU_NBT2
COLOUR_SWITCH — > active
BRIGHTNESS_AMBILIGHT — > active

((( COLOUR_SWITCH_ENSEMBLE —> 10 entries )))
And: from colour must be change from default to Licht
apparently 11 entries do not work, and the function disappears in the I drive again


FEM
CS_TYPE
two_colours
PIA_DEFAULT_CD Change to color_2
MAPPING_LCI_7_FUNCTION Change to cs_2

Regards